冰楓論壇

標題: arduino nano製作4位數字時鐘 [打印本頁]

作者: 洪嵐峰 時間: 2023-3-31 19:53
標題: arduino nano製作4位數字時鐘
arduino nano製作4位數字時鐘

製作4位數字時鐘所需材料：

Arduino Nano (ATmega328P)
DS3231 RTC模組（含電池）
共陽極4位數字7段顯示器 x 4
220歐姆電阻 x 8
杜邦線數據線（母-母）x 20
按鈕開關 x 3
麵包板 x 1
連接腳位：

DS3231 RTC模組 - Arduino Nano
SDA - A4
SCL - A5
VCC - 5V
GND - GND
共陽極4位數字7段顯示器 x 4 - Arduino Nano
A - 2
B - 3
C - 4
D - 5
E - 6
F - 7
G - 8
DP - 9
COM1 - 10
COM2 - 11
COM3 - 12
COM4 - 13
按鈕開關
調整時鐘紐 - D10
設置模式開關 - D11
單位/十位數字選擇開關 - D12
程式碼：

#include <Wire.h>
#include "RTClib.h"

RTC_DS3231 rtc;
int digitPins[] = {2, 3, 4, 5, 6, 7, 8, 9};
int comPins[] = {10, 11, 12, 13};
int hourUnitPin = 12;
int hourTenPin = 11;
int minUnitPin = 10;
int minTenPin = 9;
int setTimePin = 8;
int modePin = 7;
int setTime = 0;
int setMode = 0;
int unitMode = 1;
DateTime now;

void setup() {
  for (int i = 0; i < 8; i++) {
pinMode(digitPins[i], OUTPUT);
  }
  for (int i = 0; i < 4; i++) {
pinMode(comPins[i], OUTPUT);
  }
  pinMode(hourUnitPin, INPUT_PULLUP);
  pinMode(hourTenPin, INPUT_PULLUP);
  pinMode(minUnitPin, INPUT_PULLUP);
  pinMode(minTenPin, INPUT_PULLUP);
  pinMode(setTimePin, INPUT_PULLUP);
  pinMode(modePin, INPUT_PULLUP);
  Wire.begin();
  rtc.begin();
  if (!rtc.isrunning()) {
rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));
  }
}

void loop() {
  now = rtc.now();
  int hour = now.hour();
  int minute = now.minute();
  if (setTime) {
if (unitMode) {
   if (digitalRead(hourUnitPin) == LOW) {
      rtc.adjust(DateTime(now.year(), now.month(), now.day(), now.hour() + 1, minute, now.second()));
      delay(200);
   }
   if (digitalRead(minUnitPin) == LOW) {
      rtc.adjust(DateTime(now.year(), now.month(), now.day(), hour, now.minute() + 1, now.second()));

} else {
   if (digitalRead(hourTenPin) == LOW) {
      rtc.adjust(DateTime(now.year(), now.month(), now.day(), (now.hour() + 10) % 24, minute, now.second()));
      delay(200);
   }
   if (digitalRead(minTenPin) == LOW) {
      rtc.adjust(DateTime(now.year(), now.month(), now.day(), hour, (now.minute() + 10) % 60, now.second()));
      delay(200);
   }
}
  }
  setMode = digitalRead(modePin);
  if (setMode == LOW) {
unitMode = !unitMode;
delay(200);
  }
  setTime = digitalRead(setTimePin);
  if (setTime == LOW) {
delay(200);
setTime = digitalRead(setTimePin);
if (setTime == LOW) {
   setMode = 1;
   while (setTime == LOW) {
      now = rtc.now();
      int hour = now.hour();
      int minute = now.minute();
      for (int i = 0; i < 4; i++) {
      digitalWrite(comPins[i], HIGH);
      int digit = 0;
      if (i == 0) {
         digit = hour / 10;
      } else if (i == 1) {
         digit = hour % 10;
      } else if (i == 2) {
         digit = minute / 10;
      } else {
         digit = minute % 10;
      }
      for (int j = 0; j < 8; j++) {
         digitalWrite(digitPins[j], (digit >> j) & 0x01);
      }
      digitalWrite(comPins[i], LOW);
      delay(5);
      }
   }
   setMode = 0;
}
  }
  for (int i = 0; i < 4; i++) {
digitalWrite(comPins[i], HIGH);
int digit = 0;
if (i == 0) {
   digit = hour / 10;
} else if (i == 1) {
   digit = hour % 10;
} else if (i == 2) {
   digit = minute / 10;
} else {
   digit = minute % 10;
}
for (int j = 0; j < 8; j++) {
   digitalWrite(digitPins[j], (digit >> j) & 0x01);
}
digitalWrite(comPins[i], LOW);
delay(5);
  }
}

歡迎光臨冰楓論壇 (https://bingfong.com/)